HydroForce AS08 Injection Prespray Sprayer Pro A70109 carpet cleaning

Description

HydroForce AS08 Injection Sprayer Pro A70109  UPC 768724753175
Description
Pre-spray 10 times faster than a pump up sprayer! Finish Jobs Faster with Hydro-Force Injection Sprayers!  For those that demand the best, the Hydro-Force Injection Sprayer Pro has all the great features you've come to expect along with a new 5 qt. container that makes the best sprayer in the industry even better! You can cut your spray time in half and quickly apply carpet presprays, deodorizers, tile and grout cleaning solutions, sanitizers, protectors and more.
Features
NEW, patent-pending container design makes the Hydro-Force sprayer the most convenient sprayer on the market.
Large side-fill port – refill without removing the injector assembly
Wand holder to keep your wand off your customer's floor
Operating pressure range of 100-1,000 PSI
Eliminates annoying mixing required by pump up sprayers
High-quality quick connects allow your gun to swivel and permits quick removal
Specification
Sprays solution at either 1 to 8 or 1 to 4.
Includes a 5 qt heavy duty roto mold jug that you can fill from the rear or side w/qt. measurement markings
Jug is over twice a thick as standard blow molded jugs - designed to last a life time!
Spray gun rated at 2600 PSI and 7 GPM
Chemically resistant seals
18" stainless steel wand
Tethered cap
Compare to current or past OEM associations
A70109
AS08
UPC 768724753175
Additional Information
General Function:
The Hydro-Force Injection Sprayer is based upon an injection system that consists of a specially designed valve that injects a concentrated chemical into the high-pressure water flow from the machine. Hydro-Force is designed for use with incoming water pressure of 400 PSI. The water flow is automatically reduced as it passes through the injector valve, thus reducing the pressure approximately 64%. To obtain the actual working pressure of your Hydro-Force Injection Sprayer, multiply your incoming pressure by 36%. The Hydro-Force Injection Sprayer is factory set to inject chemicals at a 1 to 8 ratio. Other chemicals may be used but should be prepared for a 1 to 8 dilution. The Hydro-Force pressure can be increased by putting a smaller jet at the end of the wand. This will, however, decrease the injection rate of your chemical. Your injection ratio may also change depending on the viscosity (thickness) of your chemical concentrate. The 1 to 8 ratio is based upon chemicals with a similar viscosity to water. The injection ratio can also be slightly affected by your main flow water temperature. This is generally not enough of a change to appreciably change the effectiveness of your system. We do, however, recommend the water temperature be kept below 200 degrees Fahrenheit, as higher temperatures can cause problems on the injection.
Pre-Spray and Traffic Lane Applications:
Hydro-Force Injection Sprayer eliminates the hassles of measuring and mixing. We recommend you keep an extra 5-quart container or two on your truck to make sure you never run out and to facilitate quick changes of your chemical containers. Remember that Hydro-Force Injection Sprayers automatically mixes at a 1 to 8 ratio. If your 5-quart container is full then that is the same as holding an 11-gallon pump sprayer of regular, ready to use pre-spray. We have found that Hydro-Force Injection Sprayers offer better penetration and overall coverage than most other sprayers. It is therefore possible to pre-spray your jobs up to 45 minutes before you reach that area to be cleaned. An effective way to use the Hydro-Force for pre-conditioning or small to medium jobs is to start at the door coming into the house, spraying all the traffic areas, working your way to the farthest point back in your job. You have then completed your pre-conditioning in just seconds and are prepared to hook up your wand and start cleaning your way out. Keep in that your Hydro-Force is spraying 3 to 4 times the amount of product your normal pump sprayer is putting out. This means you must move quickly to avoid over-applying. Protector should be applied in even, slightly overlapping strokes.